Vendor access
This part is for Aigna staff
Vendors see their own installation and the device reference they need to build it: device types, setup guides and models. Everything else stays with Aigna.
Go to your installationModule
Projects is switched off
Projects, the schedule, planning, the work plan and the Lab. This demo has the Projects module switched off in Organisation settings.
Batch 5 of 9 · Project PRJ-21Simulated live
2 AV extenders
0 of 2 units set up · nothing to reviewchecked just now
Setup is done by Aigna's engineers. Your installs are on the Deploy page.
Once for all 2
Through Front-panel DIP switchesSet on each unit by hand Front-panel DIP switches. Keia Atlas cannot read these back, so a person confirms them.
2 settings to set and 8 to check; 0 left at the manufacturer's default.See every settingThe setup guide
The same on every unit
- Active USB Host (DIP 2B)
- On (this unit's USB is a slave)
- Power source
- EXT3-C-XR-T's own 20V adapter, run to the table end
The units
Only what differs per unit. Each unit's build sheet has every setting worked out.Nothing is ready for you here. Keia Atlas keeps checking these units.
| Unit | Provision | Install | Configure | |
|---|---|---|---|---|
| Build sheet | ||||
| Build sheet | ||||
Setup order
Optional: tick as you go, or let the checks do it1Mount EXT3-C-XR-T at the table (or credenza) and EXT3-POE-XR-R at the display/rack end.0/2
2Set the DIP-switches on both units, below, before connecting cables or power.0/2
3Connect EXT3-C-XR-T's HDBT OUT to EXT3-POE-XR-R's HDBT IN with a single certified HDBaseT cable.0/2
4Connect the room laptop to the USB-C IN on EXT3-C-XR-T; connect the display to HDMI OUT on EXT3-POE-XR-R.0/2
5Power both units from their own adapters, or let EXT3-POE-XR-R feed EXT3-C-XR-T over the HDBaseT cable (up to 19.7W) if only one adapter is run to the table.0/2
6Power-cycle both units once, since DIP-switches 2B, 3B and 4B only take effect after a restart.0/2
7Confirm the LINK LED lights on both units and that the space's USB peripherals (camera, soundbar) enumerate on the laptop.0/2
Every setting
10 in the setup guide, as patternsValues marked Per unit are patterns here. Each unit's build sheet has them worked out: 12.03 Heron, 12.03 Heron.
DIP-switches - EXT3-C-XR-T (transmitter)5
- ETH by USB (DIP 1A)Rear panel > SETUP DIP-switches > 1ACheck it is Off (ETH enabled)
Why
Passes the laptop's Ethernet link through to the receiver end, which Aigna's AV VLAN design assumes is available.
- HDBT Range Mode (DIP 2A)Rear panel > SETUP DIP-switches > 2ACheck it is Off (Standard range mode)
Why
Standard range covers Aigna's typical cable runs at full quality; only switch to Long range mode if a site's run needs the extra reach, which costs bandwidth.
- Active USB Host (DIP 2B)Rear panel > SETUP DIP-switches > 2BCheck it is Off (this unit is the active USB host)
Why
The laptop plugs in at the transmitter, so it must stay the USB host; the receiver's matching switch is changed to slave so only one side claims the role.
- IR Modulation (DIP 3B)Rear panel > SETUP DIP-switches > 3BCheck it is Off (IR pass-thru enabled)
Why
Aigna rooms don't drive an IR emitter cable from this port, so plain pass-through is correct.
- RS-232 operation Mode (DIP 4B)Rear panel > SETUP DIP-switches > 4BCheck it is Off (RS-232 firmware programming inactive)
Why
Keeps the RS-232 port carrying normal control traffic instead of sitting in firmware-upload mode.
DIP-switches - EXT3-POE-XR-R (receiver)4
- HDBT Range Mode (DIP 1A)Rear panel > SETUP DIP-switches > 1ACheck it is Off (Standard range mode)
Why
Must match the transmitter's range mode; long range only turns on together with the transmitter's, for a longer run.
- Active USB Host (DIP 2B)Rear panel > SETUP DIP-switches > 2BSet to On (this unit's USB is a slave)
Why
Both units default to host, but only one may host the USB link at a time; since Aigna's laptop connects at the transmitter, the receiver is switched to slave.
- IR Modulation (DIP 3B)Rear panel > SETUP DIP-switches > 3BCheck it is Off (IR pass-thru enabled)
Why
Matches the transmitter side so an extended IR signal passes through unmodified.
- RS-232 operation Mode (DIP 4B)Rear panel > SETUP DIP-switches > 4BCheck it is Off (RS-232 firmware programming inactive)
Why
Normal operation; only slid to the programming position during a firmware upgrade.
Power1
- Power sourceSet to EXT3-C-XR-T's own 20V adapter, run to the table end
Why
The transmitter's adapter also runs the 60W USB-C PD laptop charging; PoE sent from the receiver caps out at 19.7W, which won't charge a laptop, so Aigna runs the transmitter's own adapter whenever charging is wanted.