Keia Atlas
Healthy- SpaceOpen areas and corridors, Level 12
- ModelUbiquiti U7 Pro
- SerialDEMO-CHI-003251
- LifecycleIn service
- Target firmware5.4.1
Healthy when recorded in the area the Wi-Fi design places it; its switch port and cable recorded.
Viewing as , ,
Vendor access
This part is for Aigna staff
Vendors see their own installation and the device reference they need to build it: device types, setup guides and models. Everything else stays with Aigna.
Go to your installationModule
Assets is switched off
Device types, units, models, setup guides, standards, IT stores and cables. This demo has the Assets module switched off in Organisation settings.
Device typewireless-access-pointVersion 1.02 models
Wireless access point
73 units in service · no advisories to review
206 mm × 206 mm × 46 mm, front, to scale
Every spec and portShowing Ubiquiti U7 Pro
Ports
1 port, rear
- Width
- 206 mm
- Height
- 206 mm
- Depth
- 46 mm
- Weight
- 0.68 kg
- Power
- 21 W max
Drawing traced from Ubiquiti U7 Pro store photos, drawn as seen from below the ceiling. Ports from the vendor's documentation.
Checked on one example, chi-12-ap01 (simulated values).
Asset register
Healthy- Asset tagAG-003251
- SerialDEMO-CHI-003251
- ModelUbiquiti U7 Pro
- SpaceOpen areas and corridors, Level 12
- StatusActive
- Hostnamechi-12-ap01
Healthy when status is active; space matches where the access point is mounted.
Addresses and DNS
Healthy- Hostnamechi-12-ap01
- MAC02:E7:0B:46:16:BE
- IP address10.40.12.139
Healthy when address reservation on the management VLAN matches the MAC address; forward and reverse DNS records resolve.
Device management
Healthy- Device namechi-12-ap01
- SerialDEMO-CHI-003251
- Firmware5.4.1
Healthy when adopted and online in the UniFi Network application; firmware at the fleet standard for the model; uplink at 2.5 Gb/s and powered at PoE+; radios on the channels and widths the Wi-Fi standard sets.
Monitoring
Healthy- Monitor namechi-12-ap01
Healthy when reporting; no open critical alerts; channel use below the alert threshold.
What each field means, and how hostnames and addresses are built: Learn: device fields
Nothing to configure on Ubiquiti U7 Pro
It works as it comes, or it is set up through the device it connects to. See every setup guide.
No firmware line tracked for Ubiquiti U7 Pro
When the vendor watcher tracks a model, its releases, Aigna's decision on each, and any advisories appear here and on every device of that model.
Symptoms
Likely causes and where to look firstNo wifi in an areaAccess point offline (no PoE, cable or switch port fault); Access point not adopted after a reset; Radio disabled or on a blocked channelCheck Device management first
Slow or dropping wifiChannel crowded by neighbours; Uplink negotiated at 1 Gb/s or 100 Mb/s (cable fault); Too many clients on one radioCheck Monitoring first
Access point keeps restartingSwitch PoE budget exceeded; PoE only at 802.3af instead of PoE+; Firmware faultCheck Device management first
Cross-checks
The same fact must agree everywhere it is recorded| Check | Compares |
|---|---|
| Serial match | keia_atlas.serial = inventory.serial |
| Space match | keia_atlas.space = inventory.space |
| Hostname match | inventory.hostname = dhcp_dns.hostname |
| Firmware match | device_management.firmware_version = keia_atlas.expected_firmware |
Used in
Device type file
- File
- data/device-classes/wireless-access-point.yaml
- Version
- 1.0
- Updated
- 2026-09-29
- Hostname prefix
- ap