Vendor access
This part is for Aigna staff
Vendors see their own installation and the device reference they need to build it: device types, setup guides and models. Everything else stays with Aigna.
Go to your installationModule
Projects is switched off
Projects, the schedule, planning, the work plan and the Lab. This demo has the Projects module switched off in Organisation settings.
Batch 9 of 16 · Project PRJ-22Simulated live
1 Kramer PA-240Z amplifier
0 of 1 unit set up · nothing to reviewchecked just now
Setup is done by Aigna's engineers. Your installs are on the Deploy page.
Once for all 1
Through Device web interfaceSet on each unit by hand Device web interface. Keia Atlas cannot read these back, so a person confirms them.
3 settings to set and 6 to check; 0 left at the manufacturer's default.See every settingThe setup guide
The same on every unit
- High-Pass Filter
- On
The units
Only what differs per unit. Each unit's build sheet has every setting worked out.Nothing is ready for you here. Keia Atlas keeps checking these units.
| Unit | Hostname | Provision | Install | Configure | |
|---|---|---|---|---|---|
| Build sheet | dub-303-amp0110.20.3.59 | ||||
Setup order
Optional: tick as you go, or let the checks do it1Rack-mount PA-240Z and wire the ceiling speakers to the Hi-Z OUT terminal block.0/1
2Set DIP-switch 1 to Hi-Z and DIP-switch 2 to 70V or 100V before applying power.0/1
3Set the rear-panel master volume trimmer to a safe starting level.0/1
4Connect Ethernet, browse to the web pages, and change the default Admin/Admin login.0/1
5Set input mixing, EQ and the master volume/balance for the space from the Speaker Output page.0/1
6Confirm the space's audio (from the Poly Studio X bar or the switcher's audio out) reaches the speakers at the right level.0/1
7Firmware is applied by uploading a file on the Device Settings web page; there is no automatic-update option to turn off.0/1
Every setting
9 in the setup guide, as patternsValues marked Per unit are patterns here. Each unit's build sheet has them worked out: dub-303-amp01.
Output mode (DIP-switches)2
- Hi-Z/Lo-Z (DIP 1)Rear panel > Hi-Z/Lo-Z and 100V/70V DIP-switches > DIP 1Check it is Hi-Z (default)
Why
Aigna's Galil 6-C ceiling speakers are wired to the 70V/100V transformer taps, which needs Hi-Z mode; Lo-Z is only for a direct 4/8 ohm pair.
- 70V/100V (DIP 2)Rear panel > Hi-Z/Lo-Z and 100V/70V DIP-switches > DIP 2Check it is 100V (default)
Why
Matches Kramer's own default and the higher-voltage tap on the Galil 6-C, which keeps run current low over longer ceiling cable runs.
Network1
- DHCPDevice Settings > Ethernet SettingsCheck it is On, with a reservation on the AV VLAN
Why
Aigna's AV devices sit on a DHCP-reserved address on the AV VLAN rather than a hand-typed static one.
Security2
- Activate SecurityCheck it is Enabled (default)
Why
The web pages already prompt for a login out of the box; Aigna keeps it on.
- Web pages user name and passwordPer unitSet to From the password vault, per siteWorked out on the build sheet
Why
The default Admin/Admin login must be changed before the amplifier goes into service.
Audio3
- High-Pass FilterSet to On
Why
Cuts frequencies below 70Hz that the Galil 6-C isn't rated to reproduce, which saves amplifier headroom for a background-music/voice room.
- Bass/Mid/Treble EQCheck it is Flat (0dB), Kramer's default
Why
Left flat until a space's acoustics are measured; Aigna doesn't pre-set an EQ curve blind.
- Master VolumePer unitSet to Set per space during commissioningWorked out on the build sheet
Why
No factory default level is stated; it's set to a safe, audible level for each space's speaker count and ceiling height.
Firmware1
- Firmware update methodCheck it is Manual upload only, no automatic-update toggle exists
Why
There's nothing to turn off; firmware only changes when an installer manually uploads a file, which already matches Aigna's Lab-first policy.