Keia Atlas
Healthy- Space5.04 Briefing auditorium
- ModelPoly Studio E70
- SerialDEMO-DUB-004041
- LifecycleIn service
- Target firmware4.2.2
Healthy when recorded in the space its space type expects; every port wired as the space type says.
Viewing as , ,
Vendor access
This part is for Aigna staff
Vendors see their own installation and the device reference they need to build it: device types, setup guides and models. Everything else stays with Aigna.
Go to your installationModule
Assets is switched off
Device types, units, models, setup guides, standards, IT stores and cables. This demo has the Assets module switched off in Organisation settings.
Device typecameraVersion 1.05 models
Camera
1 unit in service · no advisories to review
321 mm × 89.1 mm × 102 mm, front, to scale
Every spec and portShowing Poly Studio E70
Ports
3 ports, rear
- Width
- 321 mm
- Height
- 89.1 mm
- Depth
- 102 mm
- Weight
- 0.907 kg
Drawing traced from HP dimensional drawing, Studio E70 front. Ports from the vendor's documentation.
Checked on one example, dub-5-04-dev01 (simulated values).
Asset register
Healthy- Asset tagAG-004041
- SerialDEMO-DUB-004041
- ModelPoly Studio E70
- Space5.04 Briefing auditorium
- StatusActive
Healthy when status is active; space matches where the device is installed.
Device management
Healthy- Device namedub-5-04-dev01
- SerialDEMO-DUB-004041
- Firmware4.2.2
Healthy when online in the vendor's device management service; firmware at the fleet standard for the model; settings match the setup guide for the model.
What each field means, and how hostnames and addresses are built: Learn: device fields
Camera·v1.0·19 Oct 2026
Studio E60/E70 as an additional camera
- ModelStudio E60, E70
- FirmwarePoly VideoOS 4.6.0 (host); Studio E60 camera software 1.1.3.6+; Studio E70 camera software 1.12.0+ for IP LLN
- ModeStand-alone
Checkingon AG-000281
Settings
7 set · 3 verify · 1 per device
New install, in order
- 1USB: connect the camera's USB-C/USB-B port to a USB-A port on the host system and power it from its own adapter, or (E70 on G62) from a PoE injector on its Ethernet port.
- 2IP LLN (Studio X72 or Studio G62 only): connect the camera's Ethernet port to the host's LLN port. The LLN port supplies no power, so power the camera from its own adapter, a PoE/PoE+ injector, or, for more than one IP camera, a Netgear ProAV M4250-9G1F-PoE+ (GSM4210PD) switch.
- 3IP LLN only: in the host's web interface, go to General Settings > Device Management, find the camera under Available Devices by its MAC address, and select Pair.
- 4In the host's web interface, go to Audio/Video > Video Inputs and set Framing Size, White Balance and Tracking Mode below.
Setup guide file state
- AssetboxIn sync
- Fleet LensIn sync
Open the setup guideConfiguring happens in a project's Deploy page.
No firmware line tracked for Poly Studio E70
When the vendor watcher tracks a model, its releases, Aigna's decision on each, and any advisories appear here and on every device of that model.
Symptoms
Likely causes and where to look firstNo camera imageNo power or PoE; Cable or converter fault; Not selected as a sourceCheck Keia Atlas first
Cross-checks
The same fact must agree everywhere it is recorded| Check | Compares |
|---|---|
| Serial match | keia_atlas.serial = inventory.serial |
| Space match | keia_atlas.space = inventory.space |
| Firmware match | device_management.firmware_version = keia_atlas.expected_firmware |
Used in
Device type file
- File
- data/device-classes/camera.yaml
- Version
- 1.0
- Updated
- 2026-09-27
- Hostname prefix